An aluminum extrusion cockpit only feels finished once the right accessories land on it. The mounts, holders, and clips in this list all share one thing in common: they slot into 8020-style profile (the T-slot aluminum rail standard that most sim rigs are built around) and turn a bare frame into a usable racing station. The picks below cover cockpit foundations, wheel mounting, streaming gear, and cable cleanup, so you can build out a sim setup that actually feels like your own rather than a workbench project.
A Fast Comparison Of The Options
Pro Sim Racing Logitech Pro QR Wheelbase Mount
Pro Sim Racing Cup Holder for Sim Rig (Large)
SimSport Gadget Stream Deck XL Enclosure Mount
Marada 8040 Aluminum Profile Simulator Cockpit
SIMPUSH Wheel Mount for Logitech RS50/G PRO
Pro Sim Racing MagSafe iPhone Charger Mount
Pro Sim Racing Fanatec Emergency Stop Mount
SSG Cable Management Clip (10 Pack)
SSG 20-Pack Knuckle Cable Management Clip
More Details On Our Top Picks
A wheelbase mount has one job: hold the wheel dead-still while a high-torque direct-drive motor tries to twist it off the rig. This Pro Sim Racing plate is cut for the Logitech Pro QR pattern, so the wheelbase drops in without shimming or drilling. Vertical orientation keeps the wheelbase close to the driver’s chest for a more race-like reach, and the machined plate gives the assembly a planted feel during hard cornering.
For racers already running 8020 extrusion across the chassis, the included M6 hardware (M6 is a 6mm metric bolt size) and T-nuts (sliding nuts that lock into the aluminum profile’s T-shaped slot) slide right into the slot and torque down without extra trips to the hardware store. It’s a focused, no-fluff piece, and it does its single job well.
Where It Delivers
- Custom-cut for the Logitech Pro QR pattern, so alignment is essentially plug-and-play.
- Accepts both horizontal and vertical 8020 profiles, useful for low-seat and upright cockpit layouts.
- Plate geometry stays rigid under hard feedback loads, with no visible flex in the bracket itself.
- Includes two M6 bolts and two T-nuts so the install is a single box, no extra parts run.
Things To Consider
- Only fits Logitech Pro QR bases, so owners of older G29 or G920 setups should look elsewhere.
- Vertical-only mounting may feel awkward for short-legged drivers who prefer a laid-back seating position.
Key Specs
Who It Suits Best
Logitech Pro owners running an 8020 extrusion cockpit who want a clean, direct bolt-on without a generic universal plate.
Skip It When
You run a Fanatec or older Logitech G-series base, in which case the Simucube or wheelbase-agnostic mounts in this category fit more cleanly.
Endurance events at Le Mans can run two, four, even twenty-four hours, and nobody wants to bail out of a stint to find a drink. The Pro Sim Racing cup holder in the large size solves a small but persistent cockpit problem: where to put a bottle without it flying off the desk under hard braking. It slides into the T-slot and stays put.
Built in Denver, Colorado, the holder spans 4040, 1515, and 8020 profile standards, so it works on the same rig as the wheelbase mount in this list. The large variant gives wider bottles and tumblers enough room to settle in without rattling, which matters when you’re shifting at Monza and don’t want a cold drink migrating to the wheel.
Where It Excels
- Large format fits bigger tumblers, sport bottles, and 32 oz insulated cups.
- Cross-compatible with 4040, 1515, and 8020 profiles, so it moves with you if you change rigs.
- Hardware is included, so there’s no separate bolt pack to order.
Points To Keep In Mind
- Mounts only on vertical or horizontal profile edges, not directly to flat panels.
- Wide-bottle drivers may find the opening tight if they run a koozie or rubber boot.
Right Fit For
Endurance racers and streamers who spend long stints in the seat and want a stable spot for drinks within arm’s reach.
Look Elsewhere When
Your cockpit is already crowded with button boxes and shifters, in which case the Stream Deck XL mount is a more space-efficient add.
A Stream Deck XL is one of the most useful streaming tools a sim racer can own, but it tends to live on a desk and slide around mid-race. The SimSport Gadget enclosure lifts it off the desk and bolts it straight to the rig’s 8020 extrusion, where it becomes part of the cockpit rather than a separate gadget. The result feels intentional rather than improvised.
The mount tilts up/down and left/right, so you can aim the keys toward a camera, a co-driver, or your own hand depending on the rig layout. Removing the mid joint shortens the reach for compact cockpits, which is a thoughtful touch for shared spaces or sim studios with tight monitor arms overhead.
A Few Strong Suits
- Two-axis tilt gives both camera-friendly and driver-friendly angles from a single bracket.
- Profile compatibility covers 4040, 8020, and 1515, so it matches most aluminum extrusion rigs.
- Mid joint can be removed to bring the Stream Deck closer to the wheel for compact layouts.
Trade Offs
- Enclosure is sized for the XL only, so the standard 15-key Stream Deck needs a different solution.
- More moving parts than a fixed bracket, so periodic re-tightening is part of routine ownership.
Made For
Streamers, coaches, and content creators who rely on hotkeys, overlays, and macros during long broadcasts and want the deck anchored to the rig.
Consider Something Else When
You want a one-piece fixed mount and don’t need tilt, in which case the Logitech Pro QR plate offers a simpler bolt-on approach for a different accessory.
Most of this list covers accessories that bolt onto an existing rig, but the Marada 8040 is the foundation under all of them. The 40×80mm main beam (a structural aluminum profile measuring 40mm by 80mm) is a step up from the lighter 40×40 frames that come in budget cockpits, and the difference shows the moment a high-torque direct-drive base goes full lock at Spa. Marada ships a black seat in the box, so the cockpit is genuinely drivable out of the package rather than waiting on a separate chair purchase.
Sliding rails along the seat and pedal plate let the rig grow with different drivers, and the embedded slot pattern means accessories like the wheelbase mount and cup holder from this list clamp right on. PlayStation 5 compatibility is built in, which matters if your racing nights are split between iRacing and Gran Turismo.
Key Advantages
- 40×80mm main extrusion provides meaningful rigidity upgrade over 40×40 frames.
- Sliding rails on seat and pedal plate support a wide range of driver heights and leg lengths.
- Standardized slot spacing accepts the same T-nut hardware as the smaller accessories in this list.
Where It May Fall Short
- Larger frame footprint, so apartment dwellers should measure the floor space first.
- Assembly time runs longer than a flat-pack wheel stand, so budget an evening for the build.
Key Specs
Best Suited To
Sim racers building a long-term cockpit around a high-torque direct-drive wheel who want the chassis to outlast two or three wheel upgrades.
Where Another Pick Suits Better
Casual drivers who just need a wheel stand should skip the full cockpit and pair the Pro Sim Racing Logitech Pro QR Wheelbase Mount with a desk clamp instead.
Not every wheel is in use at the same time, and storing a steering wheel on a hook tends to scratch the leather or worse, deform the spokes. The SIMPUSH mount cradles the wheel by the hub and keeps the rim safe, which is the kind of detail collectors notice on day one. It installs on either profile rails or directly into wall studs, so it works in a racing room or a garage workshop.
Three printing materials are available, so you can match the mount’s strength and finish to your setup. PLA (a biodegradable 3D printer filament) handles typical indoor weight fine, while PETG or ABS variants step up the heat and impact resistance for garage walls. The single M6 T-nut slot keeps hardware needs minimal.
What Stands Out
- Dual-purpose mount works on 8020 profile or wall studs, so it follows the rig or the room.
- Hub-cradle design avoids pressure on the leather rim, which keeps nicer wheels looking new.
- Multiple material options let shoppers pick a finish suited to indoor or garage environments.
Honest Caveats
- Single included profile nut, so multi-wheel owners will want a small parts box on hand.
- Limited to Logitech RS50 and G PRO wheels, so other brands need a different bracket.
Perfect Match For
Collectors and multi-wheel households that rotate between formula, GT, and rally rims and want each one displayed without damage.
Swap It Out When
You run a Fanatec or non-Logitech wheel, in which case a universal-style wheel display hook covers more bases.
An iPhone on a sim rig usually means a precarious stick-on mount and a charging cable that doesn’t quite reach. Pro Sim Racing’s MagSafe bracket solves both problems in one: the cradle is form-fitted for Apple’s MagSafe charger (the magnetic charging puck that snaps to the back of newer iPhones), so the phone aligns and starts charging the moment it clicks into place. The braided cable version adds a tougher, tangle-resistant lead that handles daily cockpit use.
Rotation between portrait and landscape is a one-handed twist, which matters when a phone doubles as a live telemetry screen or streaming camera. The mount ships from Colorado and clamps onto 4040 or 8020 profiles, matching the same rail standard as the wheelbase plate and cockpit above.
What Makes Sense
- Dual-orientation swivel moves between portrait and landscape without unmounting.
- Form-fitted to Apple’s MagSafe charger, which keeps the magnetic alignment accurate.
- Braided cable variant holds up better to the constant plug-and-unplug of sim sessions.
Where It Is Less Suited
- MagSafe charger is not included, so non-Apple shoppers should plan a separate purchase.
- Phone mount only, so a USB-C tablet or a GoPro needs a different solution.
Key Specs
Whose Shelf It Belongs On
iPhone-toting streamers and drivers who use the phone for telemetry, dash apps, or a backup camera view during long sessions.
Where A Sibling Pick Shines
Streamers who run a Stream Deck as their main hotkey surface will get more mileage from the SimSport Gadget Stream Deck XL Enclosure Mount.
The Fanatec Podium kill switch is a heavy-duty mushroom-style button designed to cut power in an instant, and it deserves a serious mount rather than a Velcro patch. This Pro Sim Racing bracket is precision-cut for that exact switch, with a clamping fit that holds the button under hard impact without shifting. The result feels more like aviation hardware than a sim accessory.
Hardware is included in the box, so the install is one trip with a hex key. Built in the United States by people who actually race, the mount is positioned for quick thumb reach on most cockpit layouts, which is the point of a kill switch in the first place.
A Favorable Mix
- Precision fit for the Fanatec Podium kill switch, with no wiggle in the clamp.
- Full hardware kit included, four M6 bolts and two T-nuts cover both 4040 and 8020 rails.
- Mounted within thumb reach, which is the whole reason a kill switch exists.
Softer Spots
- Switch-specific fit, so non-Fanatec kill buttons need a different bracket entirely.
- Adds a rigid protrusion to the cockpit, worth considering if you shift seating position often.
Built With In Mind
Fanatec Podium owners running serious force-feedback setups who want a real, hardware-mounted kill switch within easy reach during practice and races.
Reach For A Different Pick When
You run a Logitech or Thrustmaster base without a dedicated kill switch, in which case the wheelbase mount is the more relevant accessory.
A clean rig starts with cable management, and the SSG 10-pack is the simplest way to keep USB leads, power cables, and shifter cables off the floor. Each clip snaps into the T-slot of a 4040 or 8020 profile and grips the cable snugly without pinching the jacket. Owners commonly report that the clips survive repeated re-routing when swapping wheels or pedals.
Because the pack ships in a single size, it works best for rigs with one cable thickness. For mixed-gauge runs, the 20-pack variant below gives you both small and large clips in one box, which is the more flexible option for pedal-heavy or shifter-rich setups.
Practical Pluses
- Simple push-in install that takes seconds per clip, no tools required.
- Works with 4040 and 8020 profiles, so it pairs with everything else in this list.
- 10-pack covers a single-rig install with spares left over for future upgrades.
Minor Gripes
- Single clip size, so very thick power cables and thin USB leads may need different grip strengths.
Feature Snapshot
Who Will Love This
First-time cockpit builders with a single wheel and pedal set who want a tidy install without a lot of fuss.
Skip It When
Your rig runs heavy power supplies and slim USB cables through the same channels, in which case the 20-pack below handles the mix more cleanly.
The knuckle-style 20-pack solves a real sim rig problem: cable runs aren’t all the same thickness, and a one-size-fits-all clip tends to either crush a thin USB lead or let a thick power cable sag. This pack ships with 10 small and 10 large knuckle clips, so the same box covers everything from a delicate telemetry cable to a chunky power supply lead.
Fit extends across 4040 and 8020 profiles from SimLab, Trak Racer, 6-Sigma, GT-Omega, and Rigmetal cockpits. For multi-wheel households or pedal-heavy rigs with handbrakes and shifters, the size variety is what turns a tangled nest into a routed, serviceable harness.
Everyday Advantages
- Mixed small and large clips handle both slim USB and thick power cables in one box.
- Compatible with the major cockpit brands, so the clips work across most existing rigs.
- Knuckle design pivots slightly, which eases cable routing around tight frame corners.
What To Weigh
- More clips than a single-wheel rig needs, so a 10-pack may suffice for minimalist builds.
The Right Fit
Multi-wheel and pedal-heavy rigs that route mixed cable gauges through the same chassis and want one box to handle the lot.
Not Your Match When
You run a single wheel and pedal set with mostly one cable thickness, in which case the SSG 10-pack is the leaner buy.
What Matters Most When Choosing 8020 Sim Rigs
Profile Compatibility Comes First
Before any accessory or cockpit, confirm the aluminum extrusion standard in play. 8020 refers to a 20mm-wide T-slot rail in a frame that’s often 40×40mm or 40×80mm in cross-section, and 4040, 1515, and 8020 all describe different profile widths that share the same T-slot geometry. Most modern cockpits use 8020 rails as the main structural beam, with 4040 used for cross-bracing and smaller accessories.
A mismatch here means holes that don’t line up, T-nuts that fall through, or brackets that don’t clamp. The picks in this list all stay within the common 8020 and 4040 standards, which is why they pair well with most SimLab, Trak Racer, and Marada-style cockpits.
Match The Mount To The Wheelbase
Wheelbase mounts are not universal, even when they look it. The Logitech Pro QR, Fanatec Podium, and Simucube bases all use different bolt patterns, and a plate cut for one brand rarely fits another without shims. The Pro Sim Racing Logitech Pro QR mount in this list is brand-specific for that reason, and the Fanatec kill switch bracket follows the same logic.
If the wheelbase isn’t in the mount’s compatibility list, skip it. A forced fit shows up as flex under load, which is the opposite of what a high-torque direct-drive rig needs.
Think About Cable Routing Early
Cable management looks like an afterthought until the first time a USB lead pops out mid-race. The SSG clip packs in this list exist because every wire on a sim rig needs a path, and the path is easier to plan when the cockpit is still empty. Running clips along the main beam before mounting accessories takes an hour and saves years of fishing cables through tight corners.
For mixed-gauge setups, a pack with both small and large clips pays off quickly. For single-wheel simplicity, a 10-pack is enough.
Adjustability Beats Aesthetics
Sliding rails, tilt joints, and removable mid sections are unsexy features until you share the rig with a co-driver, a family member, or your own future self. A cockpit that adjusts in seat distance, wheel height, and pedal angle fits more bodies and more driving styles, and it outlasts the first or second wheel upgrade without needing a rebuild.
Key Considerations Across These Picks
Pitfalls Shoppers Hit
The most common mistake in this category is buying accessories for a profile size the rig doesn’t actually use. Some budget cockpits ship with 1515 rails, not 8020, and a 1515 mount in a 8020 slot will spin freely. Measure a rail cross-section before adding anything to the cart.
Another trap is treating a wheelbase mount as a universal plate. Brand-specific mounts exist because the bolt pattern, depth, and motor weight all vary, and a generic plate may flex under high-torque loads. Buy the bracket made for the base, even if a universal looks cheaper on paper.
Where The Extra Money Goes
Higher-tier cockpit frames like the Marada 8040 in this list cost more because the main beam is 40×80mm rather than 40×40mm, which roughly doubles the cross-section that resists twisting under load. That extra material shows up as a quieter, stiffer rig during hard force feedback.
Premium accessories from Pro Sim Racing cost more because they’re machined in the United States from billet aluminum (a solid block of aluminum cut to shape, rather than cast or printed) rather than 3D-printed or stamped steel. The upgrade is real for shoppers who keep a rig for years, because the parts don’t develop the play that printed parts tend to after a season of use.
Frequently Asked Questions
What Does 8020 Mean In Sim Racing?
8020 refers to a T-slot aluminum extrusion standard where the slot is 20mm wide, and it’s the most common rail profile used in sim racing cockpits. The 40 and 80 numbers describe the cross-section size in millimeters, with 40×40 and 40×80 being the most common beam dimensions.
Do All Sim Rig Accessories Fit 8020 Rails?
Most modern accessories fit 8020 and 4040 rails because they share the same T-slot width, but always confirm the exact profile listed in the product description. Some smaller accessories are sized only for 1515 rails and won’t clamp into a 8020 slot.
Can I Mix Brands On The Same Rig?
Yes, as long as the profile standard and T-slot width match, mounts and accessories from different brands work on the same frame. The picks in this list pair cleanly with SimLab, Trak Racer, 6-Sigma, GT-Omega, and Rigmetal cockpits.
Do I Need A Full Cockpit For Sim Racing?
Not necessarily. A wheel stand and a good seat work for many drivers, but a full cockpit adds rigidity, adjustability, and pedal stability. High-torque direct-drive wheels benefit most from a full frame, while lower-torque belt-driven wheels run fine on a stand.
How Do I Keep Cables Tidy On An Aluminum Rig?
Push-in cable clips designed for 8020 and 4040 slots are the simplest solution, and a mixed-size pack like the 20-pack in this list handles both thin USB leads and thick power cables. Route cables along the main beam before mounting accessories to keep the install clean.
The Takeaway
The right setup comes down to matching each accessory to the rig standard, the wheelbase brand, and the cable gauge actually in play. Start with the cockpit foundation if the rig is bare, add the wheelbase mount next, then layer in the cup holder, phone mount, kill switch, and cable clips as the build comes together. For most drivers, that order keeps each piece earning its keep from the first session.
